How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
Hire a Pest Control Company Now
Do you find yourself trying to locate advice about How to Install a Bathtub?
Installing a tub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard task. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open a wall to eliminate the old tub as well as position the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will certainly help you install a new bathtub in your restroom if you have already bought a new tub and do not require to transform the setup of your previous water pipelines.
Your devices and also product list ought to make up the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as adjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub must wait up until the tub has actually been utilized a minimum of once as this will settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous type must be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, leading to issues with dampness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about A Step-by-Step Guide to Installing a Bathtub? Post feedback further down. We would be glad to find out your responses about this blog entry. We are looking forward that you come back again soon. So long as you enjoyed reading our page please be sure to share it. Thanks a lot for taking the time to read it.
Go Deal Report this page